The latest updated Cisco CCNP 300-410 exam dumps contain PDF and VCE.
All test questions have been corrected and updated to ensure 100% validity. You can practice the actual test questions in the Cisco 300-410 section online first.
For complete Cisco 300-410 exam questions and answers, please visit https://www.leads4pass.com/300-410.html (PDF + VCE) Cisco 300-410 exam “Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)”.

[300-410 PDF] Cisco 300-410 pdf free from leads4pass

Free share Cisco 300-410 exam PDF from Vcecert provided by leads4pass
https://www.vcecert.com/wp-content/uploads/2021/07/lead4pass-Cisco-CCNP-300-410-Exam-Dumps-Braindumps-PDF-VCE.pdf

[300-410 practice test Q1-Q15] Free sharing of Cisco CCNP 300-410 exam questions and answers from leads4pass

QUESTION 1
DRAG DROP
Drag and drop the MPLS terms from the left onto the correct definitions on the right.
Select and Place:

Correct Answer:

QUESTION 2
Refer to the exhibit. Which option describes why the EIGRP neighbors of this router are not learning routes that are
received from OSPF?

A. The subnet defined in OSPF is not part of area 0.
B. Default metrics are not configured under EIGRP.
C. There is no overlap in the subnets advertised.
D. The routing protocols do not have the same AS number.
Correct Answer: B

QUESTION 3
Exhibit:

BGP is flapping after the Copp policy is applied. What are the two solutions to fix the issue? (Choose two)
A. Configure a three-color policer instead of two-color policer under Class COPP-CRIT1CAL-7600
B. Configure IP CEF for CoPP policy and BGP to work
C. Configure a higher value for CIR under the default class to allow more packets during peak traffic
D. Configure a higher value for CIR under the Class COPP-CRIT1CAL-7600
E. Configure BGP in the COPP-CRIT1CAL-7600 ACL
Correct Answer: CE
The policy-map COPP-7600 only rate-limit HTTP and HTTPS traffic (based on the ACL conditions) so any BGP packets
will be processed in the class “class-default”, which drops exceeded BGP packets. Therefore we have two ways to
solve this problem:
+
Add BGP to the ACL with the statement “permit tcp any any eq bgp”
+
Configure higher value for CIR in default class as 2Mbps is too low for web traffic (http and https)

QUESTION 4
After some changes in the routing policy, it is noticed that the router in AS 45123 is being used as a transit AS router for
several service provides. Which configuration ensures that the branch router in AS 45123 advertises only the local
networks to all SP neighbors?

A. Option A
B. Option B
C. Option C
D. Option D
Correct Answer: D
By default BGP advertises all prefixes to external BGP neighbors. This means that if you are multi-homed (connected to
two or more ISPs) then you might become a transit AS. For example, ISP 2 in AS 200 can send traffic to your router in
AS 100 to reach ISP 3 in AS 300 because you advertised prefixes in ISP 3 to ISP 2.

QUESTION 5
Which list defines the contents of an MPLS label?
A. 20-bit label; 3-bit traffic class; 1-bit bottom stack; 8-bit TTL
B. 32-bit label; 3-bit traffic class; 1-bit bottom stack; 8-bit TTL
C. 20-bit label; 3-bit flow label; 1-bit bottom stack; 8-bit hop limit
D. 32-bit label; 3-bit flow label; 1-bit bottom stack; 8-bit hop limit
Correct Answer: A
The first 20 bits constitute a label, which can have 2^20 values. Next comes 3 bit value called Traffic Class. It was
formerly called as experimental (EXP) field. Now it has been renamed to Traffic Class (TC). This field is used for QoS
related functions. Ingress router can classify the packet according to some criterion and assign a 3 bit value to this filed.
If an incoming packet is marked with some IP Precedence or DSCP value and the ingress router may use such a field to
assign an FEC to the packet. Next bit is Stack bit which is called bottom-of-stack bit. This field is used when more than
one label is assigned to a packet, as in the case of MPLS VPNs or MPLS TE. Next byte is MPLS TTL field which serves
the same purpose as that of IP TTL byte in the IP header
Reference: https://tools.ietf.org/html/rfc5462

QUESTION 6

Refer to the exhibit. Which subnet is redistributed from EIGRP to OSPF routing protocols?
A. 10.2.2.0/24
B. 10.1.4.0/26
C. 10.1.2.0/24
D. 10.2.3.0/26
Correct Answer: A

QUESTION 7

Refer to the exhibit. An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed. What is
the reason for this issue?
A. By default, only internal routes and external type 1 routes are redistributed into BGP
B. Only classful networks are redistributed from OSPF to BGP
C. BGP convergence is slow, so the route will eventually be present in the BGP table
D. By default, only internal OSPF routes are redistributed into BGP
Correct Answer: D
If you configure the redistribution of OSPF into BGP without keywords, only OSPF intra-area and inter-area routes are
redistributed into BGP, by default.
You can redistribute both internal and external (type-1 and type-2) OSPF routes via this command:
Router(config-router)#redistribute ospf 1 match internal external 1 external 2

QUESTION 8
Which protocol does VRF-Lite support?
A. S-IS
B. ODR
C. EIGRP
D. IGRP
Correct Answer: C

QUESTION 9
Which IGPs are supported by the MPLS LDP autoconfiguration feature?
A. RIPv2 and OSPF
B. OSPF and EIGRP
C. OSPF and ISIS
D. ISIS and RIPv2
Correct Answer: C

QUESTION 10
DRAG DROP
Drag and drop the DHCP messages from the left onto the correct uses on the right.
Select and Place:

Correct Answer:

DHCPINFORM: If a client has obtained a network address through some other means or has a manually configured IP
address, a client workstation may use a DHCPINFORM request message to obtain other local configuration parameters,
such as the domain name and Domain Name Servers (DNSs). DHCP servers receiving a DHCPINFORM message
construct a DHCPACK message with any local configuration parameters appropriate for the client without allocating a
new IP address. This DHCPACK will be sent unicast to the client.
DHCPNAK: If the selected server is unable to satisfy the DHCPREQUEST message, the DHCP server will respond with
a DHCPNAK message. When the client receives a DHCPNAK message, or does not receive a response to a
DHCPREQUEST message, the client restarts the configuration process by going into the Requesting state. The client
will retransmit the DHCPREQUEST at least four times within 60 seconds before restarting the Initializing state.
DHCPACK: After the DHCP server receives the DHCPREQUEST, it acknowledges the request with a DHCPACK
message, thus completing the initialization process. DHCPDECLINE: The client receives the DHCPACK and will
optionally perform a final check on the parameters. The client performs this procedure by sending Address Resolution
Protocol (ARP) requests for the IP address provided in the DHCPACK. If the client detects that the address is already in
use by receiving a reply to the ARP request, the client will send a DHCPDECLINE message to the server and restart the
configuration process by going into the Requesting state.
Reference https://www.cisco.com/c/en/us/support/docs/ip/dynamic-address-allocation-resolution/27470-100.html

QUESTION 11
Which command enables NAT-PT on an IPv6 interface?
A. IPv6 nat-pt enable
B. ipv6 nat
C. ipv6 nat-pt
D. ipv6 nat enable
Correct Answer: B

QUESTION 12
DRAG DROP
Drag and drop the BGP states from the left to the matching definitions on the right.
Select and Place:

Correct Answer:

QUESTION 13
Refer to the exhibit. A network engineer executes the show ipv6 ospf database command and is presented with the
output that is shown. Which flooding scope is referenced in the link-state type?

A. link-local
B. area
C. As (OSPF domain)
D. reserved
Correct Answer: B

QUESTION 14
An engineer configured policy-based routing for a destination IP address that does not exist in the routing table. How is
the packet treated through the policy for configuring the set ip default next-hop command?
A. Packets are not forwarded to the specific next hop.
B. Packets are forwarded based on the routing table.
C. Packets are forwarded based on a static route.
D. Packets are forwarded to the specific next hop.
Correct Answer: D

QUESTION 15

Refer to the exhibits. A company with autonomous system number AS65401 has obtained IP address block
209.165.200.224/27 from ARIN. The company needed more IP addresses and was assigned block 209.165.202.128/27
from ISP2. An engineer in ISP1 reports that they are receiving ISP2 routes from AS65401.
Which configuration on R1 resolves the issue?

A. Option A
B. Option B
C. Option C
D. Option D
Correct Answer: A
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/23675-27.html

---

leads4pass updates Cisco 300-410 exam questions and answers throughout the year! All exam questions are updated and corrected in real-time by Cisco experts.
Guaranteed to be true and effective! leads4pass has the most complete exam policy! To pass the Cisco 300-410 exam 100%, please click https://www.leads4pass.com/300-410.html (Total Questions: 197 Q&A) leads4pass Cisco Braindumps is trustworthy! I wish you success!

[300-410 PDF] Get free Cisco 300-410 exam PDF online: https://www.vcecert.com/wp-content/uploads/2021/07/lead4pass-Cisco-CCNP-300-410-Exam-Dumps-Braindumps-PDF-VCE.pdf